{"product_id":"pu-lepidlo-na-strechy-easygun-penosil-874-sede-750ml","title":"PU roof adhesive EasyGun PENOSIL 874 gray 750ml","description":"PENOSIL PU roof adhesive easygun 874 is designed for the installation of thermal insulation made of EPS, XPS, PIR PUR and mineral wool on flat roofs.\u003cbr\/\u003e\u003cbr\/\u003eThe thick consistency, allowing a board spacing of up to 15 mm, combined with low additional expansion and an extended correction time, significantly facilitates the installation and leveling of thermal insulation boards.\u003cbr\/\u003eHigh efficiency, combined with a short setting time of the foam adhesive, speeds up installation work.\u003cbr\/\u003eA composition that increases resistance to weathering.\u003cbr\/\u003eExcellent adhesion to many materials.\u003cbr\/\u003eReliable bond strength - high bond strength exceeding the tensile strength of the thermal insulation material.\u003cbr\/\u003eEffective and economical fastening - high efficiency up to approx. 18 m2 per can.\u003cbr\/\u003eNo sagging of the boards - a thick layer of adhesive allows correction and spacing of the boards.\u003cbr\/\u003eShort curing time - mechanical fixation possible after just 2 hours.\u003cbr\/\u003eDoes not create thermal or acoustic bridges.\u003cbr\/\u003eHigh adhesion of the adhesive to the surface.\u003cbr\/\u003eHigh elimination of thermal bridges.\u003cbr\/\u003eHigh work efficiency and clean technology.\u003cbr\/\u003e\u003cbr\/\u003eCOLOUR\u003cbr\/\u003eGrey.\u003cbr\/\u003e\u003cbr\/\u003ePACKAGING\u003cbr\/\u003eAerosol can 750 ml.\u003cbr\/\u003e\u003cbr\/\u003eUSAGE\u003cbr\/\u003eFoam adhesive designed for bonding thermal insulation in applications such as:\u003cbr\/\u003eFlat roofs: for bonding thermal insulation to bitumen vapour barriers and waterproofing.\u003cbr\/\u003eAlso used on gravel or mechanically fastened roofs to temporarily secure and level thermal insulation.\u003cbr\/\u003eFoundation walls: for attaching EPS and XPS boards to bitumen waterproofing substrates (in underground parts of buildings).\u003cbr\/\u003eExternal walls: for bonding thermal insulation to external walls in ETICS systems.\u003cbr\/\u003e\u003cbr\/\u003eAPPLICATION PROCEDURE\u003cbr\/\u003ePut on protective gloves.\u003cbr\/\u003eAdjust the adhesive flow rate by pressing the trigger and adjusting the flow control knob on the gun.\u003cbr\/\u003eThe adhesive braid should have a diameter of approx. 2-3 cm (the thickness of the adhesive braid depends on the unevenness of the substrate).\u003cbr\/\u003eApply the foam adhesive to the substrate according to the diagram below.\u003cbr\/\u003eImmediately after applying the adhesive (within 3 minutes), position the elements to be joined.\u003cbr\/\u003eThe position of the elements can be corrected for 10 minutes.\u003cbr\/\u003eThe board pressed against the substrate should be covered with adhesive on ? 5% of its surface.\u003cbr\/\u003ePermissible joint thickness ? 15 mm.\u003cbr\/\u003eFurther doweling\/walking possible after 2 hours.\u003cbr\/\u003e\u003cbr\/\u003eLIMITATIONS\u003cbr\/\u003eDoes not adhere to polyethylene (PE), polypropylene (PP) or PTFE (Teflon®).\u003cbr\/\u003eThe cured foam is sensitive to UV radiation and direct sunlight, therefore it must be covered with a suitable opaque material.\u003cbr\/\u003eDue to the wide range of possible substrates, an initial compatibility and adhesion test is recommended. Prime the surface as necessary to improve adhesion.\u003cbr\/\u003eDue to various factors that can affect the product during and after application, you should always test the product before use.\u003cbr\/\u003eThe use-by date must be observed\u003cbr\/\u003e\u003cbr\/\u003eSURFACE PREPARATION\u003cbr\/\u003eThe surfaces must be dry, free of dust, loose particles and oil. Dampen the dry surface to ensure better results.\u003cbr\/\u003e\u003cbr\/\u003eCLEANING\u003cbr\/\u003eRemove fresh adhesive with a cleaner, but be careful not to damage the polystyrene board with the cleaner.\u003cbr\/\u003eOnce cured, the foam adhesive can be removed mechanically or with a universal cleaner for cured foam. Before cleaning, a test should be carried out on an inconspicuous area.\u003cbr\/\u003eAfter finishing the work, the gun must be thoroughly cleaned - to do this, screw the can of cleaner onto the gun and press the trigger until clear liquid flows out.\u003cbr\/\u003eIf you are going to take a break from work for more than 15 minutes, clean the gun nozzle with a universal foam cleaner and lock the trigger, leaving the can screwed on until the next use.\u003cbr\/\u003eIf the foam adhesive is not completely used up after finishing the work, the can valve should also be cleaned.\u003cbr\/\u003e\u003cbr\/\u003eSTORAGE\u003cbr\/\u003eGuaranteed shelf life of 12 months from the date of production, when stored in the closed original packaging, in a dry place, at a temperature between +5 °C and +30 °C. Do not store near heat sources or in direct sunlight.\u003cbr\/\u003e\u003cbr\/\u003eSAFETY REQUIREMENTS\u003cbr\/\u003ePressurized container. Use only in well-ventilated areas. Use personal protective equipment if necessary. Keep out of reach of children. For more detailed safety information, see the label and the safety data sheet (SDS).","brand":"PENOSIL","offers":[{"title":"Default Title","offer_id":53048162353490,"sku":"06560953","price":234.0,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0954\/9624\/1490\/files\/06560953_11e3885f-0143-402c-b4ad-b625361677b4.png?v=1776149064","url":"https:\/\/tipa-production.myshopify.com\/en\/products\/pu-lepidlo-na-strechy-easygun-penosil-874-sede-750ml","provider":"TIPA","version":"1.0","type":"link"}