{"product_id":"pu-lepidlo-na-xps-desky-easygun-penosil-871-sede-750ml","title":"PU adhesive for XPS boards EasyGun PENOSIL 871 gray 750ml","description":"PENOSIL PU adhesive easygun 871 is a foam adhesive for XPS boards, ideal for fixing boards to foundations, basement walls and underground parts of buildings.\u003cbr\/\u003e\u003cbr\/\u003eProvides excellent adhesion to bitumen coatings, roofing felt, bricks, concrete and plaster.\u003cbr\/\u003eIt is characterized by immediate initial adhesion, fast setting time and high thermal insulation.\u003cbr\/\u003eIt is resistant to aging and works in a wide temperature range, which makes it a reliable choice for demanding construction applications.\u003cbr\/\u003eImmediate initial adhesion.\u003cbr\/\u003eExcellent adhesion to roofing felt and asphalt.\u003cbr\/\u003eUse in a wide temperature range from -5 °C to +30 °C.\u003cbr\/\u003eCorrection time up to 10 minutes.\u003cbr\/\u003eNext stage of work after only 2 hours.\u003cbr\/\u003e\u003cbr\/\u003eCOLOR\u003cbr\/\u003eGray.\u003cbr\/\u003e\u003cbr\/\u003ePACKAGING\u003cbr\/\u003eAerosol canister 750 ml.\u003cbr\/\u003e\u003cbr\/\u003eUSAGE\u003cbr\/\u003eFixing thermal insulation boards:\u003cbr\/\u003eMade of extruded polystyrene XPS.\u003cbr\/\u003eMade of expanded polystyrene EPS.\u003cbr\/\u003eFor substrates with bitumen waterproofing in underground parts of buildings and for mineral substrates, e.g. concrete, when performing perimeter thermal insulation.\u003cbr\/\u003e\u003cbr\/\u003eAPPLICATION PROCEDURE\u003cbr\/\u003eBefore use, read the safety instructions in the safety data sheet.\u003cbr\/\u003eThe substrate should be stable, flat, dry, free of dust, dirt, contamination, old and peeling layers of paint and coatings.\u003cbr\/\u003eBefore gluing XPS or EPS boards, the bases must be waterproofed.\u003cbr\/\u003eSubstrate penetration.\u003cbr\/\u003eThe layer of applied bitumen rubber compound can be sprinkled with mineral powder to increase its adhesion. It is worth testing the adhesion of the board to the substrate by gluing it and removing it after at least 2 hours.\u003cbr\/\u003eDo not apply the adhesive to matte or water-contaminated surfaces.\u003cbr\/\u003ePreparing the polyurethane adhesive.\u003cbr\/\u003eThe temperature of the can should be between +5°C and +25°C.\u003cbr\/\u003eShake the can thoroughly for approximately 30 seconds before use.\u003cbr\/\u003eScrew the can onto the gun.\u003cbr\/\u003eThe gun temperature must not be lower than the temperature of the can.\u003cbr\/\u003e\u003cbr\/\u003eApplication\u003cbr\/\u003eWear protective gloves.\u003cbr\/\u003eApply the polyurethane adhesive by holding the can upside down.\u003cbr\/\u003eApply the polyurethane adhesive to the board in vertical strips with a diameter of 2-3 cm, maintaining equal distances of 20-30 cm between the strips and 2-3 cm from the edge.\u003cbr\/\u003eImmediately after applying the adhesive to the thermal insulation board, place it against the wall (within 3 minutes), press firmly and level it with a long spatula.\u003cbr\/\u003eThe position of the panels can be corrected within 10 minutes of their placement on the wall.\u003cbr\/\u003eTo support the panels, you can lean them on the foundation pads; The panels can be supported until the adhesive hardens, which is approximately 10 minutes.\u003cbr\/\u003e\u003cbr\/\u003eLIMITATIONS\u003cbr\/\u003eThe product does not adhere to polyethylene, polypropylene, polyamide, silicone and Teflon.\u003cbr\/\u003eThe curing speed and correction time strongly depend on the prevailing temperature and humidity - the higher the temperature, the shorter this time; The lower the temperature and closer to the minimum application temperature, the longer the correction time may be.\u003cbr\/\u003eThe manufacturer recommends correcting the position of each glued panel.\u003cbr\/\u003eAfter opening the package of polyurethane adhesive, it should be used up within 1 week.\u003cbr\/\u003eBefore use, please read the manufacturer's technical data sheet and perform a test release of the polyurethane adhesive.\u003cbr\/\u003eDo not use in rain or strong sunlight.\u003cbr\/\u003eThe quality and technical condition of the applicator used affects the parameters of the final product.\u003cbr\/\u003eDo not use the adhesive in rooms without access to fresh air or in poorly ventilated areas and protect the container from heating above +50 °C.\u003cbr\/\u003e\u003cbr\/\u003eSURFACE PREPARATION\u003cbr\/\u003eStore the container with the gun in a vertical position (gun pointing upwards).\u003cbr\/\u003eFresh adhesive can be removed with polyurethane foam cleaner, but remember that the cleaner can damage polystyrene boards.\u003cbr\/\u003eAfter hardening, the adhesive can only be removed mechanically or with hardened foam cleaner. Before cleaning, perform a test on an inconspicuous area.\u003cbr\/\u003eIf work is to be interrupted for more than 15 minutes, clean the gun nozzle with polyurethane foam cleaner and lock the trigger, leaving the container screwed in until the next use.\u003cbr\/\u003eAfter finishing work, the gun must be thoroughly cleaned with polyurethane foam cleaner. To do this, unscrew the can of glue and spray it onto the gun sleeve and barrel. Then screw the can on\u003cbr\/\u003eApply the cleaner to the gun and drain the contents until the cleaner starts to flow out on its own. Finally, remove the can and tighten the adjusting screw.\u003cbr\/\u003e\u003cbr\/\u003eCLEANING\u003cbr\/\u003eFresh glue can be removed with polyurethane foam cleaner, but remember that the cleaner can damage polystyrene boards.\u003cbr\/\u003eOnce hardened, the glue can only be removed mechanically or with a hardened foam cleaner.\u003cbr\/\u003eAfter finishing the work, the gun must be thoroughly cleaned with polyurethane foam cleaner.\u003cbr\/\u003eApply the cleaner to the gun and drain the contents until the cleaner starts to flow out on its own. Finally, remove the can and tighten the adjusting screw.\u003cbr\/\u003e\u003cbr\/\u003eSTORAGE\u003cbr\/\u003eGuaranteed shelf life of 12 months from the date of production, when stored in the closed original packaging, in a dry place, at a temperature between +5 °C and +30 °C. Do not store near heat sources or in direct sunlight. Store and transport in an upright position.\u003cbr\/\u003e\u003cbr\/\u003eSAFETY REQUIREMENTS\u003cbr\/\u003eDo not use the adhesive in rooms without access to fresh air or in poorly ventilated areas and protect the container from heating above +50 °C.","brand":"PENOSIL","offers":[{"title":"Default Title","offer_id":53048162287954,"sku":"06560952","price":172.0,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0954\/9624\/1490\/files\/06560952_c500f4e8-c628-417b-87fd-62186b7eaa13.png?v=1776149064","url":"https:\/\/tipa-production.myshopify.com\/en\/products\/pu-lepidlo-na-xps-desky-easygun-penosil-871-sede-750ml","provider":"TIPA","version":"1.0","type":"link"}